{"id":446551,"date":"2026-01-30T03:59:07","date_gmt":"2026-01-30T03:59:07","guid":{"rendered":"https:\/\/www.newsbeep.com\/au\/446551\/"},"modified":"2026-01-30T03:59:07","modified_gmt":"2026-01-30T03:59:07","slug":"unsw-demands-enhanced-uv-testing-for-topcon-solar-cells","status":"publish","type":"post","link":"https:\/\/www.newsbeep.com\/au\/446551\/","title":{"rendered":"UNSW demands enhanced UV testing for TOPCon solar cells"},"content":{"rendered":"

The research has revealed critical gaps in current solar module testing protocols, with researchers advocating for fundamental changes to industry standards following findings that\u00a0up to one-fifth of solar PV modules degrade 1.5 times faster than average<\/a>\u00a0and that\u00a0thicker aluminium oxide layers provide superior protection against UV-induced degradation<\/a>\u00a0in TOPCon cells.<\/p>\n

Speaking to PV Tech Premium, Professor Bram Hoex and Dr Fiacre Rougieux from UNSW\u2019s School of Photovoltaic and Renewable Energy Engineering have identified manufacturing defects and inadequate testing protocols as primary contributors to premature module failures, with some systems potentially losing 45% of output by the 25-year mark or reaching end-of-life in just 11 years.<\/p>\n

Multi-stressor testing emerges as a critical requirement<\/p>\n

Dr Fiacre Rougieux, a senior lecturer at UNSW, emphasises that current IEC 61215 testing protocols miss combinations that lead to extreme degradation outcomes.<\/p>\n

\u201cWhat we show is that fast-degrading modules are more likely to have multiple degradation modes activated,\u201d Rougieux explains.<\/p>\n

\u201cBecause IEC 61215 testing is primarily a set of separate single-stressor tests run in defined sequences, it can potentially miss the combinations that create extreme outcomes.\u201d<\/p>\n

IEC 61215 is the leading international standard that establishes design qualification and type approval for terrestrial PV modules. This standard ensures that PV modules can endure long-term outdoor operation.<\/p>\n

It includes tests for environmental durability, such as exposure to UV light, humidity, and thermal cycling, as well as assessments of mechanical strength, including resistance to load and hail. The goal is to confirm that both crystalline silicon and thin-film modules will not fail prematurely.<\/p>\n

The research team recommends that manufacturers introduce multi-stressor qualification and screening that better reflects real field conditions, combining heat, humidity, voltage bias, and mechanical load simultaneously.<\/p>\n

\u201cThe most damaging cases often emerge when stresses act together rather than in isolation,\u201d Rougieux notes, highlighting a fundamental flaw in current testing approaches that evaluate individual stress factors separately.<\/p>\n

This finding has significant implications for\u00a0Australia\u2019s solar market<\/a>, where harsh environmental conditions, including high UV exposure, temperature cycling, and humidity, create the exact multi-stressor scenarios that current testing protocols fail to capture adequately.<\/p>\n

Professor Bram Hoex advocates for dramatic increases in UV exposure testing, moving beyond the commonly used 15kWh to 120kWh or higher, in line with updated international standards.<\/p>\n

\u201cI would strongly encourage manufacturers to test their solar cells under much higher ultraviolet exposure than is commonly used today,\u201d Hoex states. \u201cThis allows manufacturers to make an informed decision about how much degradation they consider acceptable.\u201d<\/p>\n

The research builds on previous findings demonstrating that thicker aluminium oxide layers are the dominant parameter limiting TOPCon UVID degradation<\/a>. However, Hoex cautions against prescriptive thickness standards, noting that multiple mitigation strategies exist beyond simply increasing aluminium oxide thickness.<\/p>\n

\u201cWhile our research clearly shows that thicker aluminium oxide layers help reduce UV-induced degradation, there are many other known, and likely unknown, ways to improve a module\u2019s resistance to UV damage,\u201d Hoex explains.<\/p>\n

\u201cFor that reason, it would be misguided to impose a fixed standard for aluminium oxide thickness.\u201d<\/p>\n

Next-generation technologies face fundamental challenges<\/p>\n

The research reveals that advanced solar cell technologies, including TOPCon<\/a> and heterojunction (HJT)<\/a> modules, are inherently vulnerable to degradation as they approach theoretical performance limits.<\/p>\n

\u201cAs silicon solar cells approach their theoretical performance limit, they also become far more vulnerable to degradation,\u201d Hoex observes.<\/p>\n

In record-setting TOPCon cells, the margin for loss has become extremely small, with total recombination so low that minor UV-induced damage can double it, leading to voltage losses exceeding 20 millivolts.<\/p>\n

The same level of damage would cause less than 5-millivolt loss in a PERC cell, demonstrating how efficiency gains create new reliability challenges.<\/p>\n

\u201cThe challenge is compounded by the fact that advanced cell designs can suffer disproportionately from the same atomic-scale damage, because their doped layers are intentionally made lighter to maximise efficiency,\u201d Hoex adds, highlighting the trade-offs between peak performance and long-term durability.<\/p>\n

Financial models require degradation reality check<\/p>\n

The research findings have direct implications for solar project financing and warranty structures, particularly as\u00a0Australia\u2019s National Electricity Market (NEM)<\/a>\u00a0continues to expand renewable energy capacity.<\/p>\n

Rougieux notes that current financial models fail to account for the reality of accelerated degradation in a meaningful fraction of modules.<\/p>\n

\u201cMost solar finance models still assume one steady, linear degradation rate, and use P50 and P90 to capture weather and modelling uncertainty,\u201d Rougieux says.<\/p>\n

\u201cWe believe financiers should also allow for a meaningful fraction of modules that fail early or degrade much faster, and test whether the project can still repay the debt in those bad cases.\u201d<\/p>\n

The recommendation extends to operational strategies, with investors advised to monitor performance closely and set aside funds or insurance for repairs or replacement of underperforming modules.<\/p>\n

Both researchers advocate for enhanced independent testing that goes beyond current IEC standards. Hoex points to organisations like KIWA PVEL<\/a> as demonstrating what is possible, but argues the industry needs more comprehensive approaches.<\/p>\n

\u201cExisting IEC tests are not designed to guarantee 25-year lifetimes; they are primarily intended to screen out early-life failures,\u201d Hoex notes. \u201cIndependent testing organisations demonstrate what is possible, but the industry needs to go further.\u201d<\/p>\n

UNSW is developing independent testing protocols that provide more realistic assessments of long-term performance, working with partners to secure funding for both research and commercial deployment of enhanced testing methodologies.<\/p>\n

Manufacturing quality control recommendations<\/p>\n

The research team\u2019s recommendations for manufacturers focus on process improvements rather than prescriptive material specifications.<\/p>\n

Stronger independent testing of randomly selected products from manufacturing lines emerges as a key recommendation, using protocols that reflect current understanding of module failure mechanisms.<\/p>\n

The approach recognises that manufacturing cost pressures contribute to quality issues while avoiding overly restrictive standards that could stifle innovation in mitigation strategies. Instead, the focus shifts to comprehensive testing that captures real-world degradation scenarios and provides manufacturers with actionable data for process optimisation.<\/p>\n

As Australia\u2019s solar industry continues to expand rapidly, these research findings provide critical insights to ensure long-term system reliability and financial viability in one of the world\u2019s most challenging solar deployment environments.<\/p>\n","protected":false},"excerpt":{"rendered":"The research has revealed critical gaps in current solar module testing protocols, with researchers advocating for fundamental changes…\n","protected":false},"author":2,"featured_media":446552,"comment_status":"","ping_status":"","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[6],"tags":[64,63,231520,229858,231521,149622,102902,105,48969,35926,64085],"class_list":{"0":"post-446551","1":"post","2":"type-post","3":"status-publish","4":"format-standard","5":"has-post-thumbnail","7":"category-technology","8":"tag-au","9":"tag-australia","10":"tag-light-induced-degredation","11":"tag-modules","12":"tag-pv-modules","13":"tag-solar-cells","14":"tag-solar-pv","15":"tag-technology","16":"tag-topcon","17":"tag-unsw","18":"tag-uv"},"_links":{"self":[{"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/posts\/446551","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/comments?post=446551"}],"version-history":[{"count":0,"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/posts\/446551\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/media\/446552"}],"wp:attachment":[{"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/media?parent=446551"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/categories?post=446551"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/tags?post=446551"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}