{"id":495569,"date":"2026-02-21T23:02:09","date_gmt":"2026-02-21T23:02:09","guid":{"rendered":"https:\/\/www.newsbeep.com\/au\/495569\/"},"modified":"2026-02-21T23:02:09","modified_gmt":"2026-02-21T23:02:09","slug":"flexible-nylon-film-generates-electricity-from-compression","status":"publish","type":"post","link":"https:\/\/www.newsbeep.com\/au\/495569\/","title":{"rendered":"Flexible nylon film generates electricity from compression"},"content":{"rendered":"

A thin sheet of nylon does not look like much on its own. But in lab tests, a film made by researchers at RMIT University<\/a> kept generating electricity after being folded, stretched, and even run over by a car, again and again.<\/p>\n

That kind of toughness matters because the basic trick the film uses is simple: squeeze it, and it produces an electric charge. Materials that do this are called piezoelectric, from the Greek word for \u201cto press.\u201d Quartz, some ceramics, and even bone can behave this way.<\/p>\n

Piezoelectric parts already sit inside modern vehicles, including fuel injectors, parking sensors, and airbag systems. The RMIT team\u2019s aim is a flexible alternative that can survive real-world punishment and harvest energy from everyday pressure and motion.<\/p>\n

Members of the RMIT University research team with the newly developed nylon\u2011film energy\u2011harvesting device. Pictured (L\u2013R): Dr Yemima Ehrnst, Dr Peter Sherrell, PhD researcher Robert Komljenovic and Associate Professor Amgad Rezk. (CREDIT: Will Wright, RMIT University) Turning tough nylon into an energy generator<\/p>\n

The work is led by Distinguished Professor Leslie Yeo and Dr Amgad Rezk, both from RMIT\u2019s School of Engineering. The first author is RMIT PhD researcher Robert Komljenovic.<\/p>\n

The team started with a durable industrial plastic called nylon-11. Nylon is known for resilience and heat resistance, and the research paper notes its use in demanding gear, including aircraft carrier arrestor cables, military equipment, and space suits. Nylon-11 can be piezoelectric<\/a> \u201cin principle,\u201d the paper says, but its performance has been hard to unlock.<\/p>\n

A big reason is that nylon-11 can crystallize into several phases. The paper explains that the phase with the most promising piezoelectric behavior has been difficult to obtain and difficult to organize well, using earlier approaches like stretching or solution processing.<\/p>\n

The RMIT method adds two forces at once while the film solidifies: intense mechanical vibration and a strong electric field. The researchers describe doing this using nanometre-amplitude surface reflected bulk waves at 10 MHz on a lithium niobate substrate, while a nylon-11 precursor solution dries under ambient conditions.<\/p>\n

Yeo summed up the promise in plain language: \u201cThis method could power next-generation devices that need to survive real-world stresses, whether that\u2019s wearable tech, sensors or smart surfaces,\u201d he said.<\/p>\n

What the measurements show<\/p>\n

The study digs into structure, then follows that structure into performance. Using operando synchrotron grazing-incidence wide-angle X-ray scattering and infrared spectroscopy<\/a>, the team reports that the process drives long-range crystal ordering, improves hydrogen-bond network ordering, and aligns molecular dipoles, all of which support stronger piezoelectric behavior.<\/p>\n

RMIT researchers Robert Komljenovic and Yemima Ehrnst preparing to test the nylon device\u2019s durability using a hammer impact setup. (CREDIT: Will Wright, RMIT University) <\/p>\n

One measure of long-range ordering, Herman\u2019s orientation function, rose to about 0.32 for the electromechanical approach, while the solvent-cast control film showed no preferential long-range order.<\/p>\n

Electrical output in compression testing separated the films even more. Under cyclic compression, the electromechanically processed film generated 110 pC of charge, compared with 0.6 pC for a solvent-cast control and 3.7 pC for a film made with mechanical vibration alone.<\/p>\n

From those measurements, the team reports a macroscale piezoelectric coefficient d33 of 11.26 \u00b1 0.3 pC N\u22121 for the electromechanical film. They also report peak-to-peak voltage of about 0.65 V at 4 G\u03a9 for that film, compared with about 0.03 V for the mechanically processed film and about 0.005 V for the solvent-cast control.<\/p>\n

In terms of power, the electromechanical films reached a power density of 12.5 \u03bcW cm\u22123, which the paper describes as a 400-fold boost over the mechanically processed film.<\/p>\n

The researchers also put guardrails around their own testing. They emphasize an in-contact compressive regime to prevent contact separation, because electrostatic forces<\/a> can otherwise inflate measured values. When they tested with a 1 mm separation, voltages rose for all films, highlighting how easy it is to accidentally measure more than piezoelectric output.<\/p>\n

Surviving a car is not the whole story<\/p>\n

Durability is where the material starts to feel less like a lab curiosity. The team reports that the electromechanical film retained function after being tapped by a finger, then compressed under a moving vehicle with a load of about 14,000 N, and then tapped again.<\/p>\n<\/p>\n

In longer testing, the films maintained a consistent response over 20,000 loading cycles under an in-contact force change of 48 N.<\/p>\n

Mechanical measurements point the same direction. Nanoindentation showed a compressive modulus Y3 of 1.99 GPa for the electromechanical film, compared with 0.91 GPa for the solvent-cast control. The paper links the improved strength to a more ordered hydrogen-bonded network, supported by shifts in infrared peaks and other measurements.<\/p>\n

Limitations and reality<\/p>\n

There are limitations, and the team reports them directly. Performance drops with heat and humidity. In one set of measurements, a d33 value of 11.4 pC N\u22121 at 25\u00b0C and 35% relative humidity fell to 3.55 pC N\u22121 at 60\u00b0C and 1.04 pC N\u22121 at 80\u00b0C. At 25\u00b0C, raising humidity to 91% relative humidity reduced d33 to 6.4 pC N\u22121, with the paper pointing to dipole relaxation and device delamination under humid conditions<\/a>.<\/p>\n

Even so, one number stands out for energy harvesting. The study reports a piezoelectric voltage coefficient g33 of 427 \u00d7 10\u22123 Vm N\u22121, which it says surpasses values previously reported for piezoelectric polymers.<\/p>\n

Rezk framed the approach as industry-friendly: \u201cWe\u2019re excited to see where prospective industry partners could take this technology, from flexible electronics to sports equipment,\u201d he said.<\/p>\n

Komljenovic focused on the physical reality of the film: \u201cThe thin-film devices are so robust, you can fold them, stretch them, even run a car over them, and they keep making power,\u201d he said.<\/p>\n

Practical implications of the research<\/p>\n

If the method scales the way the team hopes, it could support self-powered sensors in places where changing batteries is a headache. Roads and infrastructure are an obvious target, since they experience constant compression from traffic. The same pressure-to-power behavior could also fit wearables<\/a> or smart surfaces that get bent and tapped all day.<\/p>\n

The paper also positions nylon-11 as a non-fluorinated alternative to PVDF, which it describes as a polyfluorinated alkyl substance and an environmental hazard. That makes the material choice part of the story, not just the processing.<\/p>\n

The next step, the researchers say, is scaling up the technology for larger applications and exploring partnerships with industry to bring it to market.<\/p>\n

Related Stories<\/p>\n","protected":false},"excerpt":{"rendered":"A thin sheet of nylon does not look like much on its own. But in lab tests, a…\n","protected":false},"author":2,"featured_media":495570,"comment_status":"","ping_status":"","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[6],"tags":[64,63,242260,249722,113065,249723,112964,249724,249725,249726,337,121903,128,249727,249728,105,21622],"class_list":["post-495569","post","type-post","status-publish","format-standard","has-post-thumbnail","category-technology","tag-au","tag-australia","tag-energy-harvesting","tag-flexible-electronics","tag-green-good-news","tag-infrastructure-sensing","tag-innovation-news","tag-nylon-11","tag-piezoelectricity","tag-pvdf-alternative","tag-research","tag-rmit-university","tag-science","tag-self-powered-sensors","tag-smart-roads","tag-technology","tag-wearable-tech"],"_links":{"self":[{"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/posts\/495569","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/comments?post=495569"}],"version-history":[{"count":0,"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/posts\/495569\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/media\/495570"}],"wp:attachment":[{"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/media?parent=495569"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/categories?post=495569"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.newsbeep.com\/au\/wp-json\/wp\/v2\/tags?post=495569"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}